[Lista ArNOG] Consulta modulo SFP Cobre en Placa Intel.
Fernando Soto
frsoto en gmail.com
Lun Ene 14 17:33:48 ART 2019
Te paso Andres
[root en VIRTUAL1POP10 ~]# dmesg | tail -n 50
[ 7.141643] ipmi_si: Trying ACPI-specified kcs state machine at i/o address 0xca2, slave address 0x20, irq 0
[ 7.180013] ipmi_si IPI0001:00: The BMC does not support clearing the recv irq bit, compensating, but the BMC needs to be fixed.
[ 7.187969] i801_smbus 0000:00:1f.4: SMBus using PCI interrupt
[ 7.192909] mei_me 0000:00:16.0: Device doesn't have valid ME Interface
[ 7.208522] ipmi_si IPI0001:00: Found new BMC (man_id: 0x002a7c, prod_id: 0x089a, dev_id: 0x20)
[ 7.220190] input: PC Speaker as /devices/platform/pcspkr/input/input8
[ 7.223932] sd 5:0:0:0: Attached scsi generic sg0 type 0
[ 7.249492] ipmi_si IPI0001:00: IPMI kcs interface initialized
[ 7.252470] IPMI SSIF Interface driver
[ 7.267854] cryptd: max_cpu_qlen set to 1000
[ 7.277521] AVX2 version of gcm_enc/dec engaged.
[ 7.277524] AES CTR mode by8 optimization enabled
[ 7.290139] alg: No test for __gcm-aes-aesni (__driver-gcm-aes-aesni)
[ 7.290258] alg: No test for __generic-gcm-aes-aesni (__driver-generic-gcm-aes-aesni)
[ 7.347554] intel_rapl: Found RAPL domain package
[ 7.347558] intel_rapl: Found RAPL domain core
[ 7.347561] intel_rapl: Found RAPL domain dram
[ 7.354363] intel_pmc_core: initialized
[ 7.421751] iTCO_vendor_support: vendor-support=0
[ 7.423056] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
[ 7.423104] iTCO_wdt: unable to reset NO_REBOOT flag, device disabled by hardware/BIOS
[ 9.162628] Adding 7812092k swap on /dev/sda3. Priority:-2 extents:1 across:7812092k FS
[ 9.544801] device-mapper: uevent: version 1.0.3
[ 9.544970] device-mapper: ioctl: 4.37.1-ioctl (2018-04-03) initialised: dm-devel en redhat.com
[ 10.243535] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
[ 11.216594] RPC: Registered named UNIX socket transport module.
[ 11.216597] RPC: Registered udp transport module.
[ 11.216598] RPC: Registered tcp transport module.
[ 11.216599] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 11.548354] type=1305 audit(1547486415.845:4): audit_pid=5162 old=0 auid=4294967295 ses=4294967295 subj=system_u:system_r:auditd_t:s0 res=1
[ 12.833282] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 12.848237] Ebtables v2.0 registered
[ 12.879831] nf_conntrack version 0.5.0 (65536 buckets, 262144 max)
[ 12.932760] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 12.943034] Netfilter messages via NETLINK v0.30.
[ 12.946189] ip_set: protocol 6
[ 13.544378] IPv6: ADDRCONF(NETDEV_UP): eno1: link is not ready
[ 17.068705] igb 0000:02:00.0 eno1: igb: eno1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[ 17.169409] IPv6: ADDRCONF(NETDEV_CHANGE): eno1: link becomes ready
[ 59.321005] tun: Universal TUN/TAP device driver, 1.6
[ 59.321009] tun: (C) 1999-2004 Max Krasnyansky <maxk en qualcomm.com>
[ 59.322313] virbr0: port 1(virbr0-nic) entered blocking state
[ 59.322318] virbr0: port 1(virbr0-nic) entered disabled state
[ 59.322378] device virbr0-nic entered promiscuous mode
[ 59.410921] virbr0: port 1(virbr0-nic) entered blocking state
[ 59.410925] virbr0: port 1(virbr0-nic) entered listening state
[ 59.410957] IPv6: ADDRCONF(NETDEV_UP): virbr0: link is not ready
[ 59.453739] virbr0: port 1(virbr0-nic) entered disabled state
[ 76.907211] fuse init (API version 7.22)
[ 83.460096] TCP: lp registered
[root en VIRTUAL1POP10 ~]#
[root en VIRTUAL1POP10 ~]# ip link
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: eno1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode DEFAULT group default qlen 1000
link/ether ac:1f:6b:97:46:94 brd ff:ff:ff:ff:ff:ff
3: eno2: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether ac:1f:6b:97:46:95 brd ff:ff:ff:ff:ff:ff
4: enp1s0f0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether ac:1f:6b:8a:7d:7a brd ff:ff:ff:ff:ff:ff
5: enp1s0f1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether ac:1f:6b:8a:7d:7b brd ff:ff:ff:ff:ff:ff
6: virbr0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue state DOWN mode DEFAULT group default qlen 1000
link/ether 52:54:00:00:70:bc brd ff:ff:ff:ff:ff:ff
7: virbr0-nic: <BROADCAST,MULTICAST> mtu 1500 qdisc pfifo_fast master virbr0 state DOWN mode DEFAULT group default qlen 1000
link/ether 52:54:00:00:70:bc brd ff:ff:ff:ff:ff:ff
[root en VIRTUAL1POP10 ~]#
De: lista-bounces en arnog.com.ar <lista-bounces en arnog.com.ar> En nombre de Andres Pugawko
Enviado el: viernes, 11 de enero de 2019 11:32 p.m.
Para: lista en arnog.com.ar
Asunto: Re: [Lista ArNOG] Consulta modulo SFP Cobre en Placa Intel.
Que te tira el dmesg | tail -n 50 ?
Saludos Andres
El vie., 11 ene. 2019 2:55 p. m., Diego Rodriguez <drodriguez en starnetworks.com.ar <mailto:drodriguez en starnetworks.com.ar> > escribió:
Forzaste la negociación?
En Arista te ve el módulo, da link y no pasa un bit si no es modulo de Arista.
El vie., 11 de ene. de 2019 14:50, Fernando Soto <frsoto en gmail.com <mailto:frsoto en gmail.com> > escribió:
Ok pero pongo un transceiver de 1Gbps MM y levanta link OK.
Es el modulo eléctrico el q no logro hacer q levante link
[root en VIRTUAL1POP10 ~]# ethtool -m enp1s0f0
Identifier : 0x03 (SFP)
Extended identifier : 0x04 (GBIC/SFP defined by 2-wire interface ID)
Connector : 0x07 (LC)
Transceiver codes : 0x00 0x00 0x00 0x01 0x00 0x00 0x00 0x00
Transceiver type : Ethernet: 1000BASE-SX
Encoding : 0x01 (8B/10B)
BR, Nominal : 1300MBd
Rate identifier : 0x00 (unspecified)
Length (SMF,km) : 0km
Length (SMF) : 0m
Length (50um) : 550m
Length (62.5um) : 270m
Length (Copper) : 0m
Length (OM3) : 0m
Laser wavelength : 850nm
Vendor name : CISCO-FINISAR
Vendor OUI : 00:90:65
Vendor PN : GBSX0.5
Vendor rev : 11.0
Option values : 0x00 0x1a
Option : RX_LOS implemented
Option : TX_FAULT implemented
Option : TX_DISABLE implemented
BR margin, max : 0%
BR margin, min : 0%
Vendor SN : GM1709157187
Date code : 170914
Optical diagnostics support : Yes
Laser bias current : 3.520 mA
Laser output power : 0.2471 mW / -6.07 dBm
Receiver signal average optical power : 0.2156 mW / -6.66 dBm
Module temperature : 37.71 degrees C / 99.87 degrees F
Module voltage : 3.3580 V
Alarm/warning flags implemented : Yes
Laser bias current high alarm : Off
Laser bias current low alarm : Off
Laser bias current high warning : Off
Laser bias current low warning : Off
Laser output power high alarm : Off
Laser output power low alarm : Off
Laser output power high warning : Off
Laser output power low warning : Off
Module temperature high alarm : Off
Module temperature low alarm : Off
Module temperature high warning : Off
Module temperature low warning : Off
Module voltage high alarm : Off
Module voltage low alarm : Off
Module voltage high warning : Off
Module voltage low warning : Off
Laser rx power high alarm : Off
Laser rx power low alarm : Off
Laser rx power high warning : Off
Laser rx power low warning : Off
Laser bias current high alarm threshold : 12.000 mA
Laser bias current low alarm threshold : 1.000 mA
Laser bias current high warning threshold : 10.000 mA
Laser bias current low warning threshold : 2.000 mA
Laser output power high alarm threshold : 1.0000 mW / 0.00 dBm
Laser output power low alarm threshold : 0.0398 mW / -14.00 dBm
Laser output power high warning threshold : 0.7943 mW / -1.00 dBm
Laser output power low warning threshold : 0.0501 mW / -13.00 dBm
Module temperature high alarm threshold : 85.00 degrees C / 185.00 degrees F
Module temperature low alarm threshold : -10.00 degrees C / 14.00 degrees F
Module temperature high warning threshold : 80.00 degrees C / 176.00 degrees F
Module temperature low warning threshold : -5.00 degrees C / 23.00 degrees F
Module voltage high alarm threshold : 3.7000 V
Module voltage low alarm threshold : 2.9000 V
Module voltage high warning threshold : 3.6000 V
Module voltage low warning threshold : 3.0000 V
Laser rx power high alarm threshold : 1.2589 mW / 1.00 dBm
Laser rx power low alarm threshold : 0.0063 mW / -22.01 dBm
Laser rx power high warning threshold : 1.0000 mW / 0.00 dBm
Laser rx power low warning threshold : 0.0079 mW / -21.02 dBm
De: lista-bounces en arnog.com.ar <mailto:lista-bounces en arnog.com.ar> <lista-bounces en arnog.com.ar <mailto:lista-bounces en arnog.com.ar> > En nombre de Daniel Di Girolamo
Enviado el: viernes, 11 de enero de 2019 2:35 p.m.
Para: lista en arnog.com.ar <mailto:lista en arnog.com.ar>
Asunto: Re: [Lista ArNOG] Consulta modulo SFP Cobre en Placa Intel.
Ese puerto SFP+ es para módulos de 10Gb y por ese motivo no te estaría levantando un módulo que convierte a Eléctrico. No sé si se entiende lo que digo.
Daniel Di Girolamo
Cel: +54-911-6118-4789
De: lista-bounces en arnog.com.ar <mailto:lista-bounces en arnog.com.ar> [mailto:lista-bounces en arnog.com.ar] En nombre de Support Telcocom
Enviado el: viernes, 11 de enero de 2019 02:26 p.m.
Para: lista en arnog.com.ar <mailto:lista en arnog.com.ar>
Asunto: Re: [Lista ArNOG] Consulta modulo SFP Cobre en Placa Intel.
Hola Fernando, me paso algo parecido hace un tiempo.... a mi no me levando el modulo sfp en el socalo sfp+. Saludos
_____
De: "Fernando Soto" <frsoto en gmail.com <mailto:frsoto en gmail.com> >
Para: lista en arnog.com.ar <mailto:lista en arnog.com.ar>
Enviados: Viernes, 11 de Enero 2019 13:53:17
Asunto: [Lista ArNOG] Consulta modulo SFP Cobre en Placa Intel.
Buenas estimados. Necesito hacer una consulta:
Tengo un server Supermicro con una placa de Red SUPERMICRO RED AOC-STGN-I2S (trae dos slot sfp+)
Con Centos 7
Le coloque un transceiver de Cobre.
Detecta el Transceiver:
[root en VIRTUAL1POP10 ~]# ethtool -m enp1s0f0
Identifier : 0x03 (SFP)
Extended identifier : 0x04 (GBIC/SFP defined by 2-wire interface ID)
Connector : 0x07 (LC)
Transceiver codes : 0x00 0x00 0x00 0x08 0x00 0x00 0x00 0x00
Transceiver type : Ethernet: 1000BASE-T
Encoding : 0x01 (8B/10B)
BR, Nominal : 1300MBd
Rate identifier : 0x00 (unspecified)
Length (SMF,km) : 0km
Length (SMF) : 0m
Length (50um) : 0m
Length (62.5um) : 0m
Length (Copper) : 100m
Length (OM3) : 0m
Laser wavelength : 0nm
Vendor name : CISCO-FINISAR
Vendor OUI : 20:20:20
Vendor PN : 10/100/1000SFP
Vendor rev : 11.0
Option values : 0x00 0x00
BR margin, max : 0%
BR margin, min : 0%
Vendor SN : EB1806255040
Date code : 180624
[root en VIRTUAL1POP10 ~]#
Pero no logro que levante Link contra nada.
Si pongo un Tranceiver de fibra levanta link OK
Slds.
_______________________________________________
Lista mailing list
Lista en arnog.com.ar <mailto:Lista en arnog.com.ar>
http://mailmancabase.interdotnet.com.ar/mailman/listinfo/lista
--
Gustavo Figueroa
Soporte Telcocom
0810-333-5354
_______________________________________________
Lista mailing list
Lista en arnog.com.ar <mailto:Lista en arnog.com.ar>
http://mailmancabase.interdotnet.com.ar/mailman/listinfo/lista
_______________________________________________
Lista mailing list
Lista en arnog.com.ar <mailto:Lista en arnog.com.ar>
http://mailmancabase.interdotnet.com.ar/mailman/listinfo/lista
------------ próxima parte ------------
Se ha borrado un adjunto en formato HTML...
URL: <http://mailmancabase.interdotnet.com.ar/pipermail/lista/attachments/20190114/62eb1ed2/attachment-0001.html>
Más información sobre la lista de distribución Lista